[ Welcome | What's New | Download | FAQ | Related Sites | Search]
Version 3.2.11 - 1 November 2003
***WARNING***
This version will only upgrade 3.1.00 or higher. An Invalid Record Declaration will be received if it installed over any version lower.
If your version is lower than 3.1.00, download Version 3.1.00 and install it first.
***WARNING***
3.2.11 Fixed more problems on Win2000/XP systems..
Version 3.2.10 - 26 June 2003
***WARNING***
This version will only upgrade 3.1.00 or higher. An Invalid Record Declaration will be received if it installed over any version lower.
If your version is lower than 3.1.00, download Version 3.1.00 and install it first.
***WARNING***
3.2.10 Stopped Cascading the Active Link Windows. This seemed to cause some problems on Win2000/XP systems..
Version 3.2.09 - 10 June 2002
***WARNING***
This version will only upgrade 3.1.00 or higher. An Invalid Record Declaration will be received if it installed over any version lower.
If your version is lower than 3.1.00, download Version 3.1.00 and install it first.
***WARNING***
3.2.09 Moves cnclink.ini file to the same folder of the main program. It used to be stored in the Windows folder. This caused some conflict with Win2000/XP if the user did not have administrator rights.
Version 3.2.08 - 6 March 2002
***WARNING***
This version will only upgrade 3.1.00 or higher. An Invalid Record Declaration will be received if it installed over any version lower.
If your version is lower than 3.1.00, download Version 3.1.00 and install it first.
***WARNING***
3.2.08 Update dealing with Burny III downloads. When download requested, it would give a "Reload" message .
Version 3.2.07 - 10 October 2001
***WARNING***
This version will only upgrade 3.1.00 or higher. An Invalid Record Declaration will be received if it installed over any version lower.
If your version is lower than 3.1.00, download Version 3.1.00 and install it first.
***WARNING***
3.2.06 - 3.2.07 Updated Debug Capture File to write setup configurations when capture file started in an effort to aid in debugging.
Version 3.2.05 - 28 March 2001
***WARNING***
This version will only upgrade 3.1.00 or higher. An Invalid Record Declaration will be received if it installed over any version lower.
If your version is lower than 3.1.00, download Version 3.1.00 and install it first.
***WARNING***
3.2.02 - 3.2.05 are incremental works, with support being added for the Vision (Atas) Controller. At this time, file downloading only has been activated for Vision.
Version 3.2.01 - 28 February 2001
***WARNING***
This version will only upgrade 3.1.00 or higher. An Invalid Record Declaration will be received if it installed over any version lower.
If your version is lower than 3.1.00, download Version 3.1.00 and install it first.
***WARNING***
Support added to disable TurboCut CNC Link for Windows Timeout. When long files are downloaded and the Control starts cutting on the fly, CNC Link would timeout. Set the CNC Link Timeout to -1. CNC Link will wait
indefinitely, or until another download is requested.
An older way was to insert an M65 in the file being downloaded. This required the programmer to "guess" about the right place to insert the code. CNC Link now supports the M65 by adding a couple of lines to the CncLink.ini found in the Windows directory. Use the your Control name like the example below:
[Lynx]
AutoReload=M65
This should be away from other groupings in the ini file. Remember the M65 must be in the file being downloaded.
Also in version 3.2.01, the Test Terminal has been fixed to support more than Comm1. All available Comm ports can now be tested. Also fixes lock up problem in Test Terminal.
Version 3.2.00 - 3 September 2000
***WARNING***
This version will only upgrade 3.1.00. An Invalid Record Declaration will be received if it installed over any version lower.
If your version is lower than 3.1.00, download Version 3.1.00 and install it first.
***WARNING***
Sato Controller added.
Changed 3.2.00 to upgrade 3.1.00
Version 3.1.00 - 9 May 2000
***WARNING***
This version will only upgrade 3.0.05 or less. An Invalid Record Declaration will be received if it installed over any version higher.
Even re-installing on itself the error will exist, but it will not matter on a re-install. Just Ok the message and it will continue. A File Access Error will post, but it is Ok as well.
***WARNING***
A few file structure changes in this version.
Version 3.0.05 - 4 October 1999
Convert On the Fly changed to work off of the file extension. Different Rules for different file extensions for each controller. As a result, ANY RULES ALREADY SET UP WILL HAVE TO BE RESET.
Insert of a new Controller name and associated configurations not handled properly in previous versions. - Corrected this release.
One of the configuration files was not being saved by Setup in 3.0.04. - Corrected this release.
Version 3.0.04 - 26 September 1999
First release of CNC Link Convert On the Fly. Minimal changes of the CNC file during download can be accomplished by defining which codes to look for and a replacement, or additions before or after may be set up.
Help files included. Use F1 or press the Help button for explanation of individual screens.
First release where Setup tries to save previous configurations.